Home > HARDWARE > CONSTRUCTION HARDWARE > FOUNDATION HARDWARE
Choose a sub category:
ROD CHAIRS TIE WIRE / TOOLS ANCHOR BOLTS
BRICK/BLOCK LINTELS CONCRETE PIER FORMS/CAPS FLOOR JACK POSTS
FOUNDATION ACCESS DOORS REBAR PINS/REBAR CAPS NAIL STAKES
ADHESIVE ANCHORING
Sort By:
1
Used to secure the position of rebar during concrete pouring. Safely and easily twists wire bar ties. Plastic handle. Rugged design. Safely and easily twists wire bar  ties. Hardwood handle, Ergonomic design.
Makes tying fast and easy. Wood handle. Unique forming process develops high cross strength. Ample load-bearing capacity. Stiff in service. Free from sagging or buckling. All lintels should be shored until mortar has cured. Coated with black corrosion-resistant paint. Made in USA. Unique forming process develops high cross strength. Ample load-bearing capacity. Stiff in service. Free from sagging or buckling. All lintels should be shored until mortar has cured. Coated with black corrosion-resistant paint. Made in USA.
Unique forming process develops high cross strength. Ample load-bearing capacity. Stiff in service. Free from sagging or buckling. All lintels should be shored until mortar has cured. Coated with black corrosion-resistant paint. Made in USA. Nozzle kit for Ultrabond epoxy 22 oz. system.  Hi-Flow nozzles reduce waste while increasing flow. 15 inch length snaps off to 10 inches if required.  3/8 diameter at tip.  Built in mixing nut allows for fast and easy attachment to cartridge. Unique forming process develops high cross strength. Ample load-bearing capacity. Stiff in service. Free from sagging or buckling. All lintels should be shored until mortar has cured. Coated with black corrosion-resistant paint. Made in USA.
Unique forming process develops high cross strength. Ample load-bearing capacity. Stiff in service. Free from sagging or buckling. All lintels should be shored until mortar has cured. Coated with black corrosion-resistant paint. Made in USA. Flexible, hand coil packed. Ideal for tying rods or pipe products. 10 Pound coil. 170 feet in length. Black. Flexible, hand coil packed. Ideal for tying rods or pipe products. 10 Pound coil. 170 feet in length. Black.
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Made of lightweight durable plastic to give many years of trouble free use. Fits any standard size belt.
Used for securing wood and metal forms to the ground in all flatwork applications, for attaching screed bard holder clamps, for securing landscape timbers, surveying stakes, string line guides, etc. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Unique forming process develops high cross strength. Ample load-bearing capacity. Stiff in service. Free from sagging or buckling. All lintels should be shored until mortar has cured. Coated with black corrosion-resistant paint. Made in USA.
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. Used to hold rebar off grade and centered in the foundation trench. Used for securing wood and metal forms to the ground in all flatwork applications, for attaching screed bard holder clamps, for securing landscape timbers, surveying stakes, string line guides, etc.
Used to hold rebar off grade and centered in the foundation trench. Unique forming process develops high cross strength. Ample load-bearing capacity. Stiff in service. Free from sagging or buckling. All lintels should be shored until mortar has cured. Coated with black corrosion-resistant paint. Made in USA. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete.
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete.
Cast aluminum construction. Designed for left or right hand use. Large knob provides smooth operation. Accommodates all types of tie wire rolls. Used to secure the position of rebar during concrete pouring. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete.
Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Used to secure the position of rebar during concrete pouring.
Heavy gauge steel, all welded construction. Built-in lintel attached. Positive latch made to accept padlock. Door size is stenciled on each door. Primed with black corrosion resistant paint. Made in USA. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete.
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. Used to secure the position of rebar during concrete pouring. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete.
Heavy gauge steel, all welded construction. Built-in lintel attached. Positive latch made to accept padlock. Door size is stenciled on each door. Primed with black corrosion resistant paint. Made in USA. Heavy gauge steel, all welded construction. Built-in lintel attached. Positive latch made to accept padlock. Door size is stenciled on each door. Primed with black corrosion resistant paint. Made in USA. Used to secure the position of rebar during concrete pouring.
Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Use for supporting sagging floors, weak beams and warping stairways. 2-1/2" x 14 gauge prime steel inner tubing. 2-3/4" x 14 gauge prime steel outer tubing. 2-1/2" steel collar. 1-1/4" x 6" steel screw. Two 4" x 6" x 7 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. Features an in-line rod system, combined with a specifically designed friction plate that results in exceptional force making dispensing faster and reducing worker exertion and fatigue. Double gripping plates and steel trigger for increased durability and performance. For 22 Oz. cartridges, but comes with adaptable parts which allow for 16 Oz. cartridges as well.
Center hole (semi-square with round corners) enables roll to be quickly reversed for right or left hand use. Roll slips quickly onto the reel, yet easily rewinds. Continuous rolls and uniform diameters. Ideal to tie rods. Meets ASTM-A-853. 16.5 gauge. 3.5 pound coil. Used where concrete meets concrete for a stronger bond. Expansion joint filler made from resilient wood to prevent damage during expansion and contraction of concrete. Used in driveways, sidewalks, and patios, between concrete slabs and to separate slabs from structures. Meets requirements of ASTM D 1751. Mushroom style rebar safety caps protect from protruding rebar at construction sites. Bright colors for excellent visibility. Use where the danger of impalement is not present.
   
 
1