Home > HARDWARE > CONSTRUCTION HARDWARE > VENTILATION PRODUCTS > RIDGE VENTS
Sort By:
1
Tight-fitting, high-density foam end plug. To be used in conjunction with VUR ridge vents. Tight-fitting, high-density foam end plug. To be used in conjunction with LPR ridge vents. Made of corrosion-free, laminated high-density polyethylene corrugated plastic with a thin spun bound non-absorbent polypropylene membrane bonded to it which does not allow direct water or weather entry. "One-Pass" nail attachment allows for quick installment (nails included in specified items only). Draws fresh air from soffit vents and continually releases hot, moist air through the ridge line. Low profile design enables the ridge vent to virtually disappear into the roofline. 5/8" thickness. 12.7 sq. ins. of net free area. 1-3/4" nails included with specified items.
Made of corrosion-free, laminated high-density polyethylene corrugated plastic with a thin spun bound non-absorbent polypropylene membrane bonded to it which does not allow direct water or weather entry. "One-Pass" nail attachment allows for quick installment (nails included in specified items only). Draws fresh air from soffit vents and continually releases hot, moist air through the ridge line. Low profile design enables the ridge vent to virtually disappear into the roofline. 5/8" thickness. 12.7 sq. ins. of net free area. 1-3/4" nails included with specified items. Use on roof pitches from 3/12 to 20/12. Helps remove excess heat and moisture to protect against premature roof deterioration and helps prevent problems with birds, insects and animals in attic. Prevents roof rot in attic or roof deck. Minimizes peeling and extends the life of exterior and interior paint. Limits mold growth. Easy to install, shingle over design is virtually invisible when installed. Includes "Smart Nails" for hand-nailing, or 1-3/4" coil nails for nail guns. Meets or exceeds all code requirements. 16.9 sq. ins. per linear foot of net free ventilating area when hand-nailed. 14.1 sq. ins. per linear foot of net free ventilating area when using nail gun. Will not crack or dent during installation. Won't corrode, rust, or turn brittle. Works with traditional size ridge cap shingles. Shingle-over to blend into ridge line. Allows heat/condensation to escape at most effective location. Watertight, passes 110-MPH wind-driven rain test. External baffles help deflect wind/rain, no end caps needed. Prevents roof rot in attic or roof deck. Minimize peeling and extend the life of exterior and interior paint. Limit mold growth. Specially-designed louver spacing helps keep insects out. Energy-efficient, crush-resistant, with internal structural support for added durability. Extra-flexible hinge design for installation on 3:12 to 16:12 sloped roofs. 3" ring shank nails included to insure proper fastening. Edge overhang for smooth, continuous coverage between sections. Provides 18 sq.in/linear foot net-free ventilating area. 40' replaces 18 conventional or ten 12" turbine roof vents. Hip/ridge compatible with traditional sizes (11-1/2 x 12"). "EasyTear" feature allows product to be hand-torn in 3" increments. Boxed.
Can be installed with a pneumatic nail gun or hammer. Two coils of 1-3/4" nails provided. External convolute baffles - incurved design allows flexibility to roll up and out while maintaining its shape. Can be cut at one foot intervals - multiple cut lines eliminates unnecessary scrap. Weather protection and performance with no filter to clog. Molded fanfold end plug. Molded centerline. Nail holes marked every 6" - supported every foot. 11 square inches of net free ventilating area per lineal foot. External venturi baffle. Adjusts from 2/12 to 16/12 roof pitches. Limited lifetime warranty- the engineered material guarantees it will last as long as your shingles. Miami Dade County Approved 13-0701.11. 52 CFM at wind velocity of 3 MPH; 148 CFM at wind velocity of 8 MPH; 283 CFM at wind velocity of 15 MPH. For all AR10 series ridge vent. Internal aerodynamic curved baffles. 18 square inches of net free ventilating area per lineal foot. External perpendicular omni baffles. Weatherproof under-lapping joint. Four drain holes per foot per side. External venturi baffle. Pre-formed to 3/12 pitch. 10 supported nail holes.  Alignment tabs. External water shield. Slot width guide lines. Adjusts from 2/12 to 16/12 roof pitches. Co-polymer materials. Limited lifetime warranty- the engineered material guarantees it will last as long as your shingles. No connectors required. Molded fanfold end plugs - no accessories or alterations needed. Miami Dade County Approved 11-0602.03. 95 CFM at wind velocity of 3 MPH; 235 CFM at wind velocity of 8 MPH; 430 CFM at wind velocity of 15 MPH; OR4 with nails and OR4 with screen available.
Can be installed with a pneumatic nail gun or hammer. Internal aerodynamic curved baffles. External perpendicular omni baffles. Weatherproof underlapping joint. Four drain holes per foot per side. 11 square inches of net free ventilating area per lineal foot. External venturi baffle. Adjusts from 2/12 to 16/12 roof pitches. Limited lifetime warranty- the engineered material guarantees it will last as long as your shingles. Nail holes marked every 6" - supported every foot. Molded nail lines and centerline. Alignment tabs. External water shield. Slot width guide lines. Molded fanfold end plug. Miami Dade County Approved 13-0701.10. 52 CFM at wind velocity of 3 MPH; 148 CFM at wind velocity of 8 MPH; 283 CFM at wind velocity of 15 MPH. Helps resist snow infiltration in harsh winter climates. Prevent roof rot in attic or roof deck. Minimize peeling and extend the life of exterior and interior paint. Limits mold growth. Allows heat/condensation to escape at most effective location. Shingle-over design blends into ridge line. Watertight, passes 110-MPH wind-driven rain test. External baffles help deflect wind/rain, no end caps needed. 1/8" louver spacing helps keep insects out. Energy-efficient, crush-resistant, with internal structural support for added durability. Flexible 3-point hinge for installation on 3:12 to 16:12 sloped roofs. 40' replaces 18 conventional or ten 12" turbine roof vents. Quick alignment, special tabs for easy, reliable connection. No overdrive, reinforced nail holes. "EasyTear" feature allows product to be hand-torn in 3" increments. Edge overhang allows smooth, continuous coverage between sections. Provides 18 sq.in/linear foot net-free ventilating area. Works with traditional size ridge cap shingles. Boxed. Made of corrosion-free, laminated high-density polyethylene corrugated plastic with a thin spun bound non-absorbent polypropylene membrane bonded to it which does not allow direct water or weather entry. Draws fresh air from soffit vents and continually releases hot, moist air through the ridge line. Low profile design enables the ridge vent to virtually disappear into the roofline. 5/8" thickness. 12.7 sq. ins. of net free area. 1-3/4" nails included with specified items.
   
 
1