Home > PLUMBING > ROUGH PLUMBING SUPPLIES > PIPE FITTINGS > CPVC FITTINGS
Sort By:
1 2
Used to change direction in piping and features lugs for fastening. Often used in conjunction with No.530671 washer hose valve for hooking up to automatic clothes washers and for fabricating water supply piping stub outs for toilet installation. Sometimes called a Drop Ear elbow. Used in conjunction with a brass compression fitting to transition to a CPVC fitting. Replaces the ferrule. Used in conjunction with a brass compression fitting to transition to a CPVC fitting. Replaces the ferrule.
Adapts from 1/2" CPVC to 1/2" male metal pipe thread and features lugs for fastening. Used on tub and shower faucets to adapt from 1/2" CPVC riser to shower arm. Sometimes called a Drop Ear elbow. Hand tighten only; seals by means of a special elastomeric gasket to ensure leakproof seal, use of joint compound or Teflon tape is neither necessary or recommended. Solvent welds directly into 1/2'' CPVC fitting socket and adapts to female hose coupling. SLIP X SLIP Used to change direction in piping.
Used to join straight lengths of CPVC tubing. Solvent welds directly onto 1/2" CPVC tubing and adapts mechanically to 3/8" O.D. PEX tubing or copper tubing. Most often used to adapt from 1/2" CPVC tubing risers through floor to 3/8" O.D. closet or lavatory riser tubes. Can also be used with metal risers. Used to permanently or temporarily cap CPVC. Most often used in conjunction with short lengths of CPVC tubing to fabricate water hammer arrestors (air chambers) in the CPVC system. Bagged.
Used to join straight lengths of CPVC tubing. Used to adapt to female metal threaded fittings in cold water applications only! Use Teflon tape to seal pipe threads. Do not use other materials or compounds unless specifically approved by manufacturer. Used to provide a branch supply line from a main line.
Used to reduce from fitting socket to CPVC tubing. Bagged. Used to change direction in piping from a fitting socket. Also used in conjunction with a conventional CPVC 90 degree elbow to fabricate a change of direction of piping at any angle. No.52907 is 3/4" x 1/2" reducing elbow as well as 3/4" street elbow. Bagged. Allows any fitting hub to be reduced to accept PEX, copper or CPVC tubing
Solvent welds directly onto 1/2" CPVC tubing and adapts mechanically to 3/8" OD Pex or copper tubing. Most often used to adapt from 1/2" CPVC tubing risers through the wall to 3/8" OD closet and/or lavatory riser tubes. Can also be used with metal risers. Unique molded CPVC/Stainless Steel design with internal "knurl" and EPDM O'ring insures reliability and integrity. Large Stainless steel hex for easy connection to IPS sized pipe and fittings. Meets/exceeds ASTM and ANSI standards. Pressure rated to 100 psi at 180 degrees F. Made with EverTUFF CPVC and Type 304 Stainless Steel. Unique molded CPVC/Stainless Steel design with internal "knurl" and EPDM O'ring insures reliability and integrity. Large Stainless steel hex for easy connection to IPS sized pipe and fittings. Meets/exceeds ASTM and ANSI standards. Pressure rated to 100 psi at 180 degrees F. Made with EverTUFF CPVC and Type 304 stainless steel.
Solvent welds directly to CPVC tubing and provides a method for future disassembly of tubing without cutting. SLIP X SLIP Used to change direction in piping. Used to permanently or temporarily cap CPVC. Most often used in conjunction with short lengths of CPVC tubing to fabricate water hammer arrestors (air chambers) in the CPVC system. Bagged.
Used to join straight lengths of CPVC tubing to smaller size tubing. Molded CPVC/stainless steel design with internal "knurl" and EPDM O-ring insures reliability and integrity. Meets/exceeds ASTM and ANSI standards. Made with EverTUFF CPVC and Type 304 stainless steel. Pressure rated to 100 PSI at 180 degrees F. Used to adapt to female metal threaded fittings in cold water applications only! Use Teflon tape to seal pipe threads. Do not use other materials or compounds unless specifically approved by manufacturer.
Used to adapt to female metal threaded fittings in cold water applications only! Use Teflon tape to seal pipe threads. Do not use other materials or compounds unless specifically approved by manufacturer. Molded CPVC/stainless steel design with internal "knurl" and EPDM O-ring insures reliability and integrity. Meets/exceeds ASTM and ANSI standards. Made with EverTUFF CPVC and Type 304 stainless steel. Pressure rated to 100 PSI at 180 degrees F. SLIP X SLIP Used to change direction in piping.
These patented adapters solvent weld directly into standard fittings and adapt mechanically to both PEX tubing and copper tubing by utilizing a special metal gripper ring supplied with the fitting. These fittings can be used in conjunction with CPVC fittings to create an unlimited range of fittings to connect to any type of water supply tubing. Designed to compensate for the difference in coefficients of expansion which exist between CPVC and metal pipe in hot water applications. Solvent welds directly to CPVC tube and adapts to standard male pipe threads. Use Teflon tape to seal pipe threads, do not use other materials or compounds unless approved by manufacturer. Unique molded CPVC/Stainless Steel design with internal "knurl" and EPDM O'ring insures reliability and integrity. Large Stainless steel hex for easy connection to IPS sized pipe and fittings. Meets/exceeds ASTM and ANSI standards. Pressure rated to 100 psi at 180 degrees F. Made with EverTUFF CPVC and Type 304 Stainless Steel.
Unique molded CPVC/Stainless Steel design with internal "knurl" and EPDM O'ring insures reliability and integrity. Large Stainless steel hex for easy connection to IPS sized pipe and fittings. Meets/exceeds ASTM and ANSI standards. Pressure rated to 100 psi at 180 degrees F. Made with EverTUFF CPVC and Type 304 stainless steel. Used to change direction in piping from a fitting socket. Also used in conjunction with a conventional CPVC 90 degree elbow to fabricate a change of direction of piping at any angle. No.52907 is 3/4" x 1/2" reducing elbow as well as 3/4" street elbow. Bagged. 90 degree elbow. CPVC/304 stainless steel technology with internal "knurl" and EDM. O'ring insuring reliability and integrity. Meets/exceeds all ASTM and ANSI standards. Made with Ever TUFF CPVC.
Used to adapt to female metal threaded fittings in cold water applications only! Use Teflon tape to seal pipe threads. Do not use other materials or compounds unless specifically approved by manufacturer. Solvent welds directly to CPVC tubing and provides a method for future disassembly of tubing without cutting. Used to change direction in piping. Bagged.
Used to join straight lengths of CPVC tubing. Used to join straight lengths of CPVC tubing. Used to provide a branch supply line from a main line.
Used to provide a branch supply line from a main line. Designed to compensate for the difference in coefficients of expansion which exist between CPVC and metal pipe in hot water applications. Solvent welds directly to CPVC tube and adapts to standard female pipe threads. Use Teflon tape to see pipe threads, do not use other materials or compounds unless approved by the manufacturer. Designed to compensate for the difference in coefficients of expansion which exist between CPVC and metal pipe in hot water applications. Solvent welds directly to CPVC tube and adapts to standard male pipe threads. Use Teflon tape to seal pipe threads, do not use other materials or compounds unless approved by manufacturer.
Used to adapt to metal FIP threaded fittings to smaller pipe size in cold water applications only! Teflon thread tape is recommended for threaded joints. Boxed. Used to change direction in piping. Sometimes used in conjunction with a 12"L CPVC tubing on long runs to absorb expansion. Bagged. Used to transition from copper or brass tube to CPVC. Permits easy disassembly of piping system. Remove CPVC component and gasket before making sweat connection.
Used to permanently or temporarily cap CPVC. Most often used in conjunction with short lengths of CPVC tubing to fabricate water hammer arrestors (air chambers) in the CPVC system. Bagged. Designed to compensate for the difference in coefficients of expansion which exist between CPVC and metal pipe in hot water applications. Solvent welds directly to CPVC tube and adapts to standard female pipe threads. Use Teflon tape to see pipe threads, do not use other materials or compounds unless approved by the manufacturer. Connects CPVC pipe/tubing to threaded pipe. Drilled through, no tube stop.
SLIP X SLIP Used to change direction in piping. Used to reduce from fitting socket to CPVC tubing. Bagged. Used to transition from metal male pipe threads to CPVC. Permits easy disassembly of piping system.
Used to transition from metal female pipe threads to CPVC. Permits easy disassembly of piping. Used to change direction in piping. Sometimes used in conjunction with a 12"L CPVC tubing on long runs to absorb expansion. Bagged. Transition from copper or brass tube to CPVC. Permits easy disassembly of piping systems. Uses replaceable brass ferrule. Not for use with PEX tubing.
Used to transition from copper or brass tube to CPVC. Permits easy disassembly of piping system. Remove CPVC component and gasket before making sweat connection. Used to transition from metal male pipe threads to CPVC. Provides for rigid installation by mounting elbow to wall. Usually used for shower arm or washer hose valve installation. Used on close offsets where very short pieces of CPVC pipe would otherwise have to be used with conventional 45 degree elbows. A principal use is to offset piping over and around existing piping mounted on flat surfaces such as a wall or ceiling.
Used to join straight lengths of CPVC tubing. Used to transition from metal female pipe threads to CPVC. Permits easy disassembly of piping. Used to change direction in piping. Sometimes used in conjunction with a 12"L CPVC tubing on long runs to absorb expansion. Bagged.
   
 
1 2