Home > HEATING & COOLING > FIREPLACES & STOVES > STOVE PIPE & ACCESSORIES > CHIMNEY PIPE ACCESSORIES
Sort By:
1 2
Ameri-Vent 8RSC Double Wall Round Storm Collar Ameri-Vent 10RSC Double Wall Round Storm Collar Ultra Temp 208450 Type A Locking Band
Use with HS chimney roof flashing to insure water tight installation. Use with HS chimney roof flashing to insure water tight installation. Ultra Temp Locking Band, Type A, Stainless Steel, 8 in Width, For use with Chimney Pipe
Selkirk 206810 Storm Collar Selkirk 208810 Storm Collar Selkirk 206480 Finishing Collar
Designed to fit on the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after proper positioning. Designed to fit on the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after proper positioning. Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee.
AmeriVent 6SWA Single Wall Adapter Selkirk 208480 Finishing Collar AmeriVent 8SWA Single Wall Adapter
Included in ceiling support assembly, roof support assembly and tee assembly. Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee. Included in ceiling support assembly, roof support assembly and tee assembly.
Sure-Temp 206465 Fire Stop/Joist Shield Sure-Temp 208790 Spark Arrestor Sure-Temp 206520 Wall Band
Prevents or delays the rapid spread of fire (regardless of the cause) in a home or building. The sheet metal firestop prevents the chimney passageway from becoming an easy pathway for fire to spread from one floor to another. Diamond shaped 1/2" x 1" mesh, 18-8 stainless steel. Fits same size round chimney top. Keeps foreign objects out of chimney. Used along the wall to provide for 2" clearance and assure stability. Useful for suspending offsets. Required at 8' or closer intervals to stabilize the chimney, wherever it is supported along a vertical wall.
American Metal 6HS-SBA 3-Wall Wall Bracket Selkirk 206488 Trim Plate Spacer FMI 12S-8DM 2-Wall Chimney Support
Bracket for supporting the chimney pipe offsets, securing outdoor chimney to exterior wall. Used to trim the ceiling when a chimney is supported from above and extended down into room. Also used in conjunction with firestop/joist shield. Inner and outer pipe. The outer pipe, made of galvanized steel, provides cooling air necessary to maintain safe chimney temperatures, while the inner pipe, made of stainless steel, emits gases out of the fireplace. Snap- lock design. 12" standard pipe (12" inner diameter, 15 3/8" outer diameter) UL127 Listed 1700 Degree Pipe.
Sure-Temp 208520 Wall Band American Metal 8HS-SBA 3-Wall Chimney Support Bracket Assembly FMI 30FS-8DM Fire Stop Spacer
Used along the wall to provide for 2" clearance and assure stability. Useful for suspending offsets. Required at 8' or closer intervals to stabilize the chimney, wherever it is supported along a vertical wall. Bracket for supporting the chimney pipe offsets, securing outdoor chimney to exterior wall. For Comfort Flame systems only.
Selkirk 206512 Adjustable Pitch Ceiling Plate Ultra Temp 206450 Type A Locking Band American Metal 6FFU 3-Wall Round Roof Vent Flashing
Provides a finished appearance where the chimney passes through a sloped ceiling. Matte black finish. Adjusts to multiple roof pitches. Covers 4" space around chimney pipe (or 2" further than the required clearance). Ultra Temp Locking Band, Type A, Stainless Steel, 6 in Width, For use with Chimney Pipe Standard flashings fit various pitch roofs. Its double seamed construction protects from water leakage.
Sure-Temp 206400 Anchor Plate Sure-Temp 206435 Interior Resupport Selkirk 206240 Drip less Smoke Stove Pipe Adapter
Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy gauge steel construction for long life. Retains chimney with a twist-lock connection. Allows for two different methods of chimney resupport. First method is used at the immediate section of chimney above the upper elbow of an offset. Second method is used primarily when the immediate sections of the upper offset do not pass through a joist area and resupport is necessary. Support band is clamped around the chimney immediately below a locking band.  Straps are nailed to suitable framing at two inch clearance. For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of Sure-Temp-Type HT chimney pipe.
Selkirk 206242 Drip less Smoke Stove Pipe Adapter Sure-Temp 206463 Insulated Wall Thimble Selkirk 208240 Drip less Smoke Stove Pipe Adapter
For use in retrofit installations, this part can be installed from below with a finish support package and secured with screws. Note: Not for use with coal burning stoves. Installs quickly and eliminates need for using individual firestops. Round shielding acts as a radiation shield and provides the required 2" air space clearance to combustibles. The 2 sections telescope to accommodate 6" to 11" wall thickness. The hole opening in the faceplate for No. 206463 is 8.25"; for No. 207463 - 9.25"; and No. 208463 - 10.25". For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of Sure-Temp-Type HT chimney pipe.
Sure-Temp 200420 Roof Support Sure-Temp 200250 Roof Support Selkirk A 206825 Adjustable Roof Flashing
Fits all roof pitches and requires only simple framing. Brackets and mounting hardware only. Flexible roof support designed to fit 5, 6, 7, and 8" diameter chimney. The heavy duty band allows you to slide the length vertically to properly position this section in the system. The URSA can hold up to 30 feet of pipe, only 20 feet can be below. Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings.
American Metal 8FFU 3-Wall Round Roof Vent Flashing Sure-Temp 208463 Insulated Wall Thimble Sure-Temp 206800 Round Type HT Chimney Topper
Standard flashings fit various pitch roofs. Its double seamed construction protects from water leakage. Installs quickly and eliminates need for using individual firestops. Round shielding acts as a radiation shield and provides the required 2" air space clearance to combustibles. The 2 sections telescope to accommodate 6" to 11" wall thickness. The hole opening in the faceplate for No. 206463 is 8.25"; for No. 207463 - 9.25"; and No. 208463 - 10.25". Designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft.
Sure-Temp 206430 Type HT Wall Support Kit Sure-Temp 208400 Anchor Plate Sure-Temp 206490 Attic Insulation Shield
Tested for use fully enclosed and has been designed in 5, 6, 7 and 8 inch sizes to carry up to 60' of height. Intended for use with the Insulated Tee as an interior or exterior support where the chimney has a lateral connection. Also useful where the pipe connection passes through a combustible interior or exterior wall. Braces may only be fastened to the wall above or below the plate for chimneys which penetrate through the wall. Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy gauge steel construction for long life. Retains chimney with a twist-lock connection. Used wherever a ceiling support, finish support, firestop or joist shield is installed below an open attic. Required to guard against the hazard of blown-in or blanket insulation filling any framed opening or contacting the chimney and possible storage of combustibles against the chimney.
Selkirk A 208825 Adjustable Roof Flashing AmeriVent 6HS-WTP 3-Wall Chimney Wall Thimble Sure-Temp 206440 Roof Brace Kit
Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings. Used with tee branch and chimney section to provide proper clearance to combustible materials. Matte black painted surface for interior wall eliminates need for trim plate. Chimney support, use whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load, and to prevent damage from static and sliding snow. It should be used, at a midpoint on the chimney. Bracket adjusts from 4' to 6'.
American Metal 6HS-CSA 3-Wall Ceiling Support Assembly Sure-Temp 208430 Type HT Wall Support Kit Sure-Temp 208440 Roof Brace Kit
Use when chimney is installed in standard ceiling. 6" and 8" sizes fit between regular 16" O.C. ceiling joists. For exposed beam ceiling installations, use Roof Support. Cartoned to contain stainless steel matte black single wall adaptor. Tested for use fully enclosed and has been designed in 5, 6, 7 and 8 inch sizes to carry up to 60' of height. Intended for use with the Insulated Tee as an interior or exterior support where the chimney has a lateral connection. Also useful where the pipe connection passes through a combustible interior or exterior wall. Braces may only be fastened to the wall above or below the plate for chimneys which penetrate through the wall. Chimney support, use whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load, and to prevent damage from static and sliding snow. It should be used, at a midpoint on the chimney. Bracket adjusts from 4' to 6'.
AmeriVent 8HS-WTP 3-Wall Chimney Wall Thimble American Metal 6HS-RCS Insulated Chimney Cap Sure-Temp 208490 Attic Insulation Shield
Used with tee branch and chimney section to provide proper clearance to combustible materials. Matte black painted surface for interior wall eliminates need for trim plate. Round termination features its own built-in spark arrestor. Protects against rain, debris and birds entering chimney. Used wherever a ceiling support, finish support, firestop or joist shield is installed below an open attic. Required to guard against the hazard of blown-in or blanket insulation filling any framed opening or contacting the chimney and possible storage of combustibles against the chimney.
Sure-Temp 208800 Round Type HT Chimney Topper Sure-Temp Ultra-Temp 206410 Square Ceiling Support American Metal 8HS-CSA 3-Wall Ceiling Support Assembly
Designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft. With proper framing, all ceiling supports provide at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height. Use when chimney is installed in standard ceiling. 6" and 8" sizes fit between regular 16" O.C. ceiling joists. For exposed beam ceiling installations, use Roof Support. Cartoned to contain stainless steel matte black single wall adaptor.
Sure-Temp Ultra-Temp 206411 Round Ceiling Support FMI 30E-8DM Offset and Return Elbow American Metal 6HS-WS 3-Wall Wall Support
With proper framing, ceiling supports provide at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height. FMI Offset and Return Elbow, 8 in Nominal, 30 deg Offset, For Wood Burning at 1700 deg Standard Pipes With clean out, heavy gauge base support the chimney tee and chimney. Includes removable outer wall tee cap for clean-out.
American Metal 6HS-RSA12 3-Wall Chimney Roof Support Sure-Temp Ultra-Temp 208410 Square Ceiling Support Sure-Temp 206420 Type HT Roof Support Kit
For exposed-beam ceiling installations. Available in flat to 6/12 pitch (Standard) and for steeper pitches of 7/12 to 14/12. Can be used up to 22/12 with double wall connector. Use ceiling support when chimney is to be installed in standard ceiling. Contains stainless steel matte black single wall adaptor. With proper framing, all ceiling supports provide at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height. Contains one 18" length of pipe, roof brackets and necessary hardware. Note: Not for use with coal burning stoves.
FMI V12F-8DM Roof Flashing Sure-Temp 206600 Type HT Roof Termination Kit American Metal 8HS-RSA12 3-Wall Roof Support
For 12" standard and high temperature pipe. Includes the basic components for a standard installation; CT - Round Top,  AF-6 - Adjustable Flashing, and SC - Storm Collar. 2/12 - 6-12 pitch. For exposed-beam ceiling installations. Available in flat to 6/12 pitch (Standard) and for steeper pitches of 7/12 to 14/12. Can be used up to 22/12 with double wall connector. Use ceiling support when chimney is to be installed in standard ceiling. Contains stainless steel matte black single wall adaptor.
AmeriVent 8HS-RCS 3-Wall Round Vent Cap Sure-Temp 208420 Type HT Roof Support Kit Selkirk 206100 Insulated Chimney Tee with Tee Cap
Round termination features its own built-in spark arrestor. Protects against rain, debris and birds entering chimney. Contains one 18" length of pipe, roof brackets and necessary hardware. Note: Not for use with coal burning stoves. Used to start chimneys indoors or outdoors using a wall support assembly or a masonry pier. A length of insulated chimney pipe is attached to the Tee snout, using a Locking Band, to pass safely through combustible walls. An Insulated Tee Cap is included which can be removed from bottom opening for inspection and cleanout. Maximum height of chimney which can be supported by an insulated Tee is 50'.
   
 
1 2